The selection of Roots blower shall be appropriate, and the material quantity shall not be greater than the discharge quantity of the blower itself, so as to avoid excessive pressure, which may cause motor burning. The viscosity of the material should not be too high, which can prevent the blower motor from burning out in a short time.
The motor connector of Roots blower air lock valve shall not be false to avoid burning. The working time is not easy to be too long to avoid burning. Because the impeller of Roots blower runs without friction in the body, it does not need lubrication, so that the discharged gas does not contain oil. It is the ideal pneumatic conveying gas source for chemical industry, food industry and other industries. The rotating speed of the blower of the rotary fan is high, and the clearance between the rotor and the rotor, and between the rotor and the body is small, so there is less leakage and high volumetric efficiency. The rotor of the blower has been checked for static and dynamic balance. The finished product runs smoothly with minimal vibration.
The ventilation effect around Roots blower is good, and the motor is easy to burn out if the heat dissipation is not good. Roots blower is mainly composed of the following six parts: motor, air filter, blower body, air chamber, base (also used as oil tank), and oil drip nozzle. The blower operates eccentrically by the rotor offset in the cylinder, and allows the volume change between the blades in the rotor slot to suck in, compress and discharge air. The surrounding environment of the blower should be cleaned up. If it is too dirty, the heat dissipation efficiency of the motor radiator will be reduced, resulting in burning.
1、 Motor phase failure operation
This is a killer of three-phase asynchronous motor. When the motor operates normally, the three-phase load is symmetrical load, so the three-phase current is basically balanced and the size is equal. If the motor loses phase during operation (the phenomenon that any phase in the three-phase winding is disconnected is called phase loss), the fan vibration will become larger, abnormal noise will appear, the speed will drop, the current will increase, and the motor temperature will rise sharply, As a result, the motor will burn out. An ordinary motor will burn out in ten minutes at most. The most terrible thing is the phase failure of the whole power supply system. In addition, the switches of many equipment are self-locking or automatically opened (such as fans and pumps). The power transmission phase failure accident after a power failure may burn more than a dozen motors at a time.
2、 Bearing damage
Due to the continuous operation of Roots blower for a long time, the temperature rise of the motor body is too high, and the bearing is not replenished with grease in time, resulting in bearing oil shortage until the bearing is damaged, shaft bending, belt fracture and other phenomena, resulting in the stator and rotor friction (commonly known as barrel sweeping) leading to a sharp rise in core temperature, burning groove insulation, turn to turn insulation, The winding turns are short circuited or "shot" to the ground is caused from the surface. In serious cases, the stator core will be inverted, misaligned, the shaft will be worn, and the end cover will be scrapped. Bearing damage is generally caused by the following reasons:
1. Improper bearing assembly, such as uneven tapping on the inner ring of the bearing during cold assembly, which causes the shaft to be worn, resulting in the loss of interference between the inner ring of the bearing and the outer ring or the reduction of the interference, resulting in the inner ring running; uneven tapping when installing the motor end cover, resulting in loose matching between the end cover bearing chamber and the outer ring of the shaft, resulting in the outer ring running. Running either the inner ring or the outer ring will cause the temperature rise of the bearing to rise sharply. As long as the bearing is in good condition, intermittent running of the outer ring is allowed.
2. The bearing wall is not cleaned, or the grease is not clean. For example, in order to keep the small steel materials of the bearing thoroughly cleaned, the bearing will burn out due to excessive temperature rise due to damage caused by rolling of the bearing during operation.
3. When the bearing is replaced and processed again, the interference of the motor end cover after nesting is too large or the ovality exceeds the standard, which causes the bearing ball clearance to be too small or uneven, which causes the friction force to increase when the bearing runs, and the temperature rises sharply until it is burned out.
4. Due to axial misalignment of stator and rotor iron cores or insufficient precision after re machining of the rotating shaft, the inner and outer rings of the bearing are not on the same section, which causes the temperature of the bearing to rise after "eating hard" operation until it is burned.
5. The bearing is damaged due to the mixing of different types of grease.
6. The bearing itself has quality problems, such as rust spots on the raceway, inflexible rotation, too small clearance, cage deformation, etc.
7. The standby machine has not operated for a long time, the grease has deteriorated, and the bearing has rusted. The only way to maintain it is to pay attention to regular inspection and regular replacement of the same brand of grease during use.
3、 Overload burning will be caused when the air valve is closed
Since the air valve of Roots blower has not been opened or has not been opened enough after starting. Under this condition, the Roots blower runs, resulting in a sharp rise in the operating temperature of the motor body until it is burned out. After the air outlet or air valve is reset, the Roots blower is not closed in time, and the operation of Roots blower in this case will also cause the temperature of the motor body to rise sharply until it is burned out.
4、 Be affected with damp
The insulation reduction caused by water ingress or moisture of the distribution cabinet or motor is also a common cause of damage, but there is no way to protect it. Only pay attention to and shake the insulation regularly during use. Before the motor explodes, it can be solved by drying and re dipping. Especially for the motor driven by frequency converter, be more careful about this item, otherwise it may be reimbursed together with the frequency converter.
5、 Others
In addition, there are not very common reasons: for example, the voltage is too low or too high, the vibration causes the terminal to be loose and short circuit between phases, pests and rats, and the voltage of imported motors does not match the domestic voltage. Various depressurized starting circuit faults cause no conversion, and the motor works at low voltage for a long time, etc. The accident rate can be reduced by checking all indicators before use and then starting
I believe that after reading the above, you should also know how to prevent the Roots blower motor from burning down. I hope it will help you.
Text term label: Roots blower
Link to this article: //wuhanzhcs.com/html/news/n02/661.html
