During the daily use of Roots blower, attention must be paid to the daily maintenance, so that too many problems will not occur during the use. Today, I will take you to know what should be paid attention to when changing the oil of Roots blower
The lubricating oil of roots blower bearing should be replaced at least once every six months when it is used normally. When it is used for the first time, it should be replaced after about 200 hours of operation. The second oil change should be conducted in 1 to 2 months. After that, the lubricating oil should be checked once a week. If the lubricating oil is not deteriorated, the oil change can be extended to once every 2 to 4 months, The specified brand of lubricating oil must be used for replacement, and the old oil in the oil tank must be completely drained and cleaned before new oil can be filled.
When changing the oil, drain the oil in the oil tank first and then inject new oil. It is better not to add the oil on the basis of the old oil, because the oil in the oil tank will be too dirty and thick after a long time. This will affect the operation of Roots blower. Pay attention to the position of the oil mirror during daily inspection. Once the oil level is found to be less than half of the oil mirror, it should be supplemented in time. If the Roots blower is short of oil for a long time, the motor will burn down in serious cases.
First, let's talk about the fuel volume. All the equipment that needs to be refueled has a fuel window scale. If not, I can't give you other suggestions. In case of oil replenishing, it is generally the equipment with oil leakage. Generally, good equipment rarely has obvious oil level drop, and it is not necessary to replenish oil during the normal oil change period.
The sequence of gear oil replacement for Roots blower: first remove the gear oil, and then inject new gear oil. The first time: one month after startup and operation, the second time after three months, and the second time after long-term operation every six months. Pay attention to the oil level daily and replenish it in time.
Evaluation of lubricating oil quantity of Roots blower: the oil quantity of each model of Roots blower can check the gear side oil mirror at any time, and keep the oil level between the center line during shutdown. If the oil level is lower than the middle position, lubricating oil must be added in time; If the oil level is higher than the middle position, the oil temperature will be high, the exhaust body will spray oil, and the engine body will leak oil.
Storage of Roots blower lubricating oil: after filling the gear oil, the remaining gear oil shall not be directly exposed to the outside world to prevent other pollutants from entering the barrel and causing oil pollution; Secondly, the oil products shall be kept away from the fire source and the fire-fighting equipment shall be placed. After use, tighten the sealing cap to keep the oil drum sealed. The new oil and waste oil shall be placed separately, and the container with waste oil shall not be filled with new oil to prevent pollution. The frequency of oil change is reasonable from 2000 to 3000 based on most industrial and mining data. There are also those that are replaced diligently, and they should be replaced every March. If there are spare parts that are being switched, it is obviously unreasonable to replace them every month. The running time of the equipment shall be accumulated according to the actual use of the unit. Generally, the new machine manufacturer will require replacement at 500 hours, and then at 2000 hours. If the oil quality is good, it can be extended appropriately. Then the quality of the oil can be seen in the future oil change. If the oil is very dark and deteriorated by visual inspection, the replacement period should be shortened. The color of the oil window can also be observed for the uncertainty in the early stage, and the oil quality can be observed for part of the emissions under the hot engine state.
The oil level of each model of Roots blower can be checked at any time to keep the oil level between the center line during shutdown. If the oil level is lower than the middle position, lubricating oil needs to be added in time. If the oil level is higher than the middle position, oil leakage will occur.
Storage of Roots blower lubricating oil: after filling the gear oil, the remaining gear oil shall not be directly exposed to the outside world to prevent other pollutants from entering the barrel and causing oil pollution; Secondly, oil products shall be kept away from fire sources and fire extinguishing equipment shall be placed. After use, tighten the sealing cap to keep the oil drum sealed. The new oil and waste oil shall be placed separately, and the container with waste oil shall not be filled with new oil to prevent pollution.
I believe that after reading the above, you should also understand the problems that need attention when changing the oil of Roots blower. I hope it will be helpful to you.
Text term label: Roots blower
Link to this article: //wuhanzhcs.com/html/news/n02/603.html
